Vogel's MotionMount

The motionmount integration集成将 Home Assistant 与您的设备、服务等连接和集成。 [Learn more] allows you to control the position of your TVM 7675 Pro SIGNATURE MotionMount from Vogel’s.

This integration uses the Ethernet (IP) connection of your MotionMount. It’s not possible to connect using the RS-232 connection.

It provides information about the current position of the mount and allows setting a new position.

A use case would be to position the TV based on whether anyone is actively watching. The MotionMount provides an HDMI connection to monitor whether the TV is turned on and in response move it to a preset position or the last known position. However, if you also use the TV for background music, you probably don’t want the MotionMount to extend. By using a presence sensor to check whether anyone is actually in front of the TV, you can ensure the MotionMount only extends when the TV is actively being watched.

配置

要将 Vogel’s MotionMount integration 添加到您的 Home Assistant 实例中，请使用此 My 按钮：

Vogel’s MotionMount 可以被 Home Assistant 自动发现。如果发现了实例， 它将显示为 已发现。您可以立即进行设置。

Removing the integration

This integration follows standard integration removal. No extra steps are required.

从Home Assistant中移除集成实例

1. 前往 设置 > 设备与服务 并选择集成卡片。
2. 从设备列表中，选择要删除的集成实例。
3. 在条目旁边，选择三个点 菜单。然后，选择 删除。

Data updates

The MotionMount pushes new data to the integration. The only exception is the presets. Changes to the presets are polled数据轮询是定期查询设备或服务以检查更新或检索数据的过程。通过定义自定义轮询间隔，您可以控制系统检查新数据的频率，这有助于优化性能并减少不必要的网络流量。 [Learn more], by default every 60 seconds.

Known limitations

The integration does not provide the ability to configure the MotionMount. All settings, including configuring presets, should be done via the MotionMount app.

Only IP connections are supported. Connection via RS-232 or Bluetooth Low Energy is not supported.

Supported devices

The following devices are supported:

• TVM 7675 Pro (SIGNATURE MotionMount with Pro extension)

Unsupported devices

The following devices are not supported:

• TVM 7675 (SIGNATURE MotionMount without Pro extension)
• TVM 7355 (NEXT MotionMount)

Supported functionality

Entities

Sensors

• Moving

  • Description: Indicates whether the MotionMount is moving.

• Error Status

  • Description: The error status of the MotionMount.
    • None: There is no error.
    • Motor: There is a problem communicating with the motor.
    • HDMI CEC: There is a problem communicating with the TV. Check the HDMI cable.
    • Obstruction: The MotionMount detected an obstacle and stopped moving.
    • TV Width Constraint: The MotionMount detected that the TV moved too close to the wall and stopped moving.
    • Internal: There is an internal error. Refer to the MotionMount app for support.

Numbers

• Extension

  • Description: The current extension of the MotionMount from the wall.

• Turn

  • Description: The current rotation of the MotionMount.

Selects

• Presets
  • Description: If the MotionMount is at a preset location, this shows the corresponding preset. Any preset can be selected to move the MotionMount to this preset position.

Troubleshooting

Can’t connect to device

1. Make sure the device is powered on.
2. Make sure the device is connected to the same network as Home Assistant.
3. Make sure the IP address of the MotionMount is configured correctly.
   • In case of doubt, perform a network reset by holding the reset button for approx. 5 seconds.
     • Result: The LED will start to blink slowly. This indicates that the network configuration is being reset to use DHCP.
     • Important: Don’t hold the reset button for too long (approx. 10 s). Holding the button for 10 s or longer starts a factory reset. A factory reset is indicated by the LED blinking fast.